【限時特價有優惠，香港行貨】日本HIKOKI高壹(HITACHI日立) 18V無刷鎚鑽 DH18DPA -淨機 HIKOKI
【限時特價有優惠，香港行貨】日本HIKOKI高壹(HITACHI日立) 18V無刷鎚鑽 DH18DPA -淨機 HIKOKI

[Limited time special offer, Hong Kong licensed product] Japan HIKOKI 18V Brushless Hammer Drill DH18DPA - Clean Machine

sold in last hours
People are viewing this right now
HK$1,999.00 HK$680.00
Add to WishlistCompare
Ask a Question
Description

DH18DPA pictures

ability cement 18mm
ironwork 13mm
Carpentry 18mm
No-load revolutions
(When the temperature is 20°C and fully charged) 		NORMAL mode 0~1,080/min (times/minute)
LOW mode 0-800 /min (times/minute)
No-load strike count
(When the temperature is 20°C and fully charged) 		NORMAL mode 0-5,500 /min (times/minute)
LOW mode 0-4,100 /min (times/minute)
Body size (length x height x width) 271 x 211 x 81mm (with battery installed)
Weight (with battery installed) 2.5kg (including side handle)
2.3kg (without side handle)
Battery Model Name BSL36A18
Voltage capacity 18V-5.0Ah
Charging time About 75 minutes
charger Model Name

UC18YFSL

The best balance of compactness and lightness

  • The compact and lightweight body places the center of gravity close to your hand, making it easy to hold and operate.

    ※ The weight shown is with BSL36A18 lithium battery and without side handle

    The distance from the hand to the tip is 231 mm, the distance from the hand to the center of gravity is 81 mm, and the mass is 2.3 kg.

Top -notch drilling speed

  • Quick drilling of commonly used small diameter sizes.

    Comparison of drilling speed *2 (average drill diameter 3.5 to 10 mm)
    (Compare with our traditional product DH18DSL)

    1. As of October 2020. Among Japanese domestic power tool manufacturers (according to our research) (13-18mm class / 2 modes / 18V cordless hammer drill)
    2. The values ​​are for reference only (depending on material and conditions)
    The drilling speed of DH18DPA is about 23% faster than our conventional product DH18DSL.

Low vibration

  • The anti-vibration rubber absorbs shocks and vibrations transmitted to the handle.

    Image of shockproof rubber

    Low Vibration Comparison (Reference) *
    3-axis composite value (m/ s2 )

    The 3-axis composite value of DH18DPA is 9.9m/s2, which is about 18% lower than the 12.1m/s2 of the conventional product DH18DSL.
    • The values ​​are for reference only (depending on material and conditions)

High brightness and brightness with LED lights

  • The target position is easy to see and the work can be carried out smoothly.

    LED Light Image

Switch according to the work content Equipped with 2-stage speed switching

  • Punching holes in brittle materials becomes easy by pressing the changeover switch and reducing the number of revolutions and impacts.

    Illustration of the transfer switch and indicator light

Supports stable drilling and improves the efficiency of continuous work Equipped with automatic stop function

  • Equipped with an "auto stop function", it is very convenient when performing continuous drilling. Stores the drilling time and automatically stops the motor at the stored time.

    For example, if it takes 10 seconds from power on to power off, the 10 seconds will be stored and the next drilling will automatically stop within 10 seconds.
Please note
It will record the drilling time, but it cannot guarantee the drilling depth. Due to differences and changes in posture during work, pressure on the machine, and work materials, the drilling depth may not be constant. To reduce the difference in drilling depth, use a depth gauge together.

Reaction Force Control (RFC) for sudden loads

  • If the drill bit is suddenly overloaded, the slip clutch will be activated.
    Alternatively, a controller built into the tool body stops the motor, thereby reducing tool body vibration.

    RFC Description
    Please note
    Depending on the operating conditions, it may not work or may not perform to its fullest extent. When working, be careful when installing and securing materials and hold the tool body firmly.

Amount of work you can do on one full charge (estimated) *

Job Description Capacity Amount of work you can do on one full charge (estimated) *
Drilling concrete Depth 30mm,
Drill bit diameter 3.5mm 		5.0Ah (MV battery) Approx. 305
Depth 30mm,
Drill bit diameter 10.5mm 		5.0Ah (MV battery) Approx. 130
  • These figures are for reference only. It depends on the material and conditions.
Reviews